When do i add conditioner to my pool

It affords a small amount of protection to the chlorine from UV light, and it also acts to supplement the pools conditioner level, as it is gradually reduced by backwashing and splashing. Chlorine, which contains conditioner, is usually marked with the words "Sun-Shielded". Usually, only tablets and some granular chlorines contain conditioner. Unstabilized Chlorine : Unstabilized chlorine refers to chlorine, which does not contain conditioner.

This type of chlorine is generally used a method of super chlorination, and is not recommended as the primary source of the swimming pool's chlorine residual. The scale begins at zero ppm and has no upper limit.

Unlike chlorine, CYA does not evaporate. It remains in the pool water until it is either splashed out, backwashed, or drained.

It can also be diluted when water is added or after heavy rains. Pools open year-round should test the CYA concentration levels in the water at regular intervals. Those opened in the springtime should be tested only after the pool filter has been on and circulating the water for about three to five days.

This is because cyanuric acid is denser than water, and without the filter on and water circulating, it sinks and settles on the bottom of the pool. Keep in mind, if using stabilized chlorine each week, trichlor tablets or dichlor shock , that CYA is added with each application. Knowing how to add stabilizer to a pool is just as important as knowing when.

To achieve the recommended amount of 30 ppm, add one pound of CYA stabilizer per 4, gallons of water. Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.

So, doing the quick math, if your pool conditioner is 50 ppm, you should shoot for free chlorine levels between 3 ppm and 4 ppm. You should use about 4 lbs of CYA per 10, gallons of water for every 30 ppm it needs to be raised.

Some product instructions vary, though, so be sure to read the label for proper dosage. Can you over shock a pool? Start off by adding 3 or 4 gallons, and if you see no results overnight, add 3 or 4 more gallons the next day. Continue this process until you notice the water changing color to either cloudy white, light green or clear. The more you add, the quicker it will clear!

Is baking soda a pool stabilizer? Baking Soda is used for raising the total alkalinity of the pool, which is the key to keeping the ph in balance. It's not a stabilizer. You can get it in liquid or granule form, or mixed with chlorine tablets or sticks trichlor and in chlorine shock dichlor.

If your CYA levels dip too low, your chlorine will be completely gone in a few hours and your swimming pool will become susceptible to bacteria and algae growth. If the pool stabilizer levels get too high, however, it overpowers the chlorine and makes it less effective. It can even lead to chlorine lock , making chlorine tests read negative even when you know there is some in there.

Unless your pool is exposed to sunlight, it should be able to maintain the right chlorine levels fairly well. Opinions vary a little among experts about the proper level of CYA a pool should have, but as a general rule, it should not dip below 30 ppm or rise above 50 ppm. Most of the time, levels above 50 ppm cause chlorine lock, which is where you have added plenty of chlorine but your tests are reading 0. You'll still need to monitor your available chlorine levels with your chlorine stabilizer at 50 ppm or lower; you can do this with consistent water testing.

A good rule of thumb is to keep your sanitizer levels at round 7. So, doing the quick math, if your pool conditioner is 50 ppm, you should shoot for free chlorine levels between 3 ppm and 4 ppm.

You should use about 4 lbs of CYA per 10, gallons of water for every 30 ppm it needs to be raised. Some product instructions vary, though, so be sure to read the label for proper dosage.